<div dir="ltr"><div dir="ltr">On Thu, Feb 13, 2020 at 11:16 PM Alan Cudmore <<a href="mailto:alan.cudmore@gmail.com">alan.cudmore@gmail.com</a>> wrote:<br></div><div class="gmail_quote"><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">"set scheduler-locking on" in GDB works! I was able to run RPI2 hello.exe<br>
<br>
So I consider your instructions ready to go in the repo.<br>
More Pi 2 SMP debugging when I get the time..<br>
Thanks!<br>
Alan<br>
<br></blockquote><div>Great. But just a caution, QEMU support raspberry pi is very much incomplete</div><div>so any exception or problem may be from QEMU side and not RTEMS. So if any</div><div>test goes wrong, try running it on a real board.</div><div><br></div><div>Thanks,</div><div>Niteesh</div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
On Thu, Feb 13, 2020 at 12:30 PM G. S. Niteesh <<a href="mailto:gsnb.gn@gmail.com" target="_blank">gsnb.gn@gmail.com</a>> wrote:<br>
><br>
> On Thu, Feb 13, 2020 at 10:57 PM Alan Cudmore <<a href="mailto:alan.cudmore@gmail.com" target="_blank">alan.cudmore@gmail.com</a>> wrote:<br>
>><br>
>> I get exceptions when trying to run hello.exe.<br>
>> I'm using qemu-system-arm v 2.11.1 from ubuntu. Should I try using the<br>
>> one built by RSB?<br>
><br>
> No this should be fine. Can you post a screenshot of the output?<br>
>><br>
>> I was trying to get this setup to try RPI 2 SMP in QEMU. I may want to<br>
>> get the latest repo and do a clean build to try this again.<br>
><br>
> SMP doesn't work well with QEMU. Did you try set scheduler-locking on in GDB?<br>
> Running the executables directly in QEMU doesn't work.<br>
>><br>
>> Thanks,<br>
>> Alan<br>
>><br>
>> On Thu, Feb 13, 2020 at 12:12 PM G. S. Niteesh <<a href="mailto:gsnb.gn@gmail.com" target="_blank">gsnb.gn@gmail.com</a>> wrote:<br>
>> ><br>
>> > On Thu, Feb 13, 2020 at 10:40 PM Alan Cudmore <<a href="mailto:alan.cudmore@gmail.com" target="_blank">alan.cudmore@gmail.com</a>> wrote:<br>
>> >><br>
>> >> Hi Niteesh,<br>
>> >> I have followed your instructions for getting RTEMS running on the Pi<br>
>> >> 1 and 2. SMP currently is not working on the 2 for me, but that is not<br>
>> >> a problem with these instructions.<br>
>> >> I started to try running on QEMU following your instructions but have<br>
>> >> not been able to get time to complete my tests.<br>
>> ><br>
>> > What problem are you exactly facing?<br>
>> >><br>
>> >><br>
>> >><br>
>> >> But this is a vast improvement over "TODO", so I recommend accepting<br>
>> >> this change.<br>
>> >><br>
>> >> Thanks for creating this,<br>
>> >> Alan<br>
>> >><br>
>> >> On Thu, Feb 13, 2020 at 1:49 AM G. S. Niteesh <<a href="mailto:gsnb.gn@gmail.com" target="_blank">gsnb.gn@gmail.com</a>> wrote:<br>
>> >> ><br>
>> >> > Can someone take a look at this, It has been unnoticed for quite a while.<br>
>> >> ><br>
>> >> > Thank you,<br>
>> >> > Niteesh<br>
>> >> ><br>
>> >> > On Sat, Jan 25, 2020 at 10:49 PM G S Niteesh <<a href="mailto:gsnb.gn@gmail.com" target="_blank">gsnb.gn@gmail.com</a>> wrote:<br>
>> >> >><br>
>> >> >> Added instructions to run examples on raspberrypi.<br>
>> >> >> ---<br>
>> >> >>  user/bsps/arm/raspberrypi.rst | 111 +++++++++++++++++++++++++++++++++-<br>
>> >> >>  1 file changed, 110 insertions(+), 1 deletion(-)<br>
>> >> >><br>
>> >> >> diff --git a/user/bsps/arm/raspberrypi.rst b/user/bsps/arm/raspberrypi.rst<br>
>> >> >> index 4ef75bd..72889a5 100644<br>
>> >> >> --- a/user/bsps/arm/raspberrypi.rst<br>
>> >> >> +++ b/user/bsps/arm/raspberrypi.rst<br>
>> >> >> @@ -5,4 +5,113 @@<br>
>> >> >>  raspberrypi<br>
>> >> >>  ===========<br>
>> >> >><br>
>> >> >> -TODO.<br>
>> >> >> +This BSP supports `Raspberry Pi 1` and `Raspberry Pi 2` currently.<br>
>> >> >> +The support for `Raspberry Pi 3` is work under progress.<br>
>> >> >> +The default bootloader on the Raspberry Pi which is used to boot Raspbian<br>
>> >> >> +or other OS can be also used to boot RTEMS. U-boot can also be used.<br>
>> >> >> +<br>
>> >> >> +Setup SD card<br>
>> >> >> +----------------<br>
>> >> >> +<br>
>> >> >> +The Raspberry Pis have an unconventional booting mechanism. The GPU<br>
>> >> >> +boots first, initializes itself, runs the bootloader and starts the CPU.<br>
>> >> >> +The bootloader looks for a kernel image, by default the kernel images must<br>
>> >> >> +have a name of the form ``kernel*.img`` but this can be changed by adding<br>
>> >> >> +`kernel=<img_name>` to ``config.txt``.<br>
>> >> >> +<br>
>> >> >> +You must provide the required files for the GPU to proceed. These files<br>
>> >> >> +can be downloaded from<br>
>> >> >> +`the Raspberry Pi Firmware Repository <<a href="https://github.com/raspberrypi/firmware/tree/master/boot" rel="noreferrer" target="_blank">https://github.com/raspberrypi/firmware/tree/master/boot</a>>`_.<br>
>> >> >> +You can remove the ``kernel*.img`` files if you want too, but don't touch<br>
>> >> >> +the other files.<br>
>> >> >> +<br>
>> >> >> +Copy these files in to a SD card with FAT filesystem.<br>
>> >> >> +<br>
>> >> >> +Kernel image<br>
>> >> >> +------------<br>
>> >> >> +<br>
>> >> >> +The following steps show how to run ``hello.exe`` on a Raspberry Pi 2.<br>
>> >> >> +The same instructions can be applied to Raspberry Pi 1 also.<br>
>> >> >> +Other executables can be processed in a similar way.<br>
>> >> >> +<br>
>> >> >> +To create the kernel image:<br>
>> >> >> +<br>
>> >> >> +.. code-block:: none<br>
>> >> >> +<br>
>> >> >> +     $ arm-rtems5-objcopy -Obinary hello.exe kernel.img<br>
>> >> >> +<br>
>> >> >> +Copy the kernel image to the SD card.<br>
>> >> >> +<br>
>> >> >> +Make sure you have these lines below, in your ``config.txt``.<br>
>> >> >> +<br>
>> >> >> +.. code-block:: none<br>
>> >> >> +<br>
>> >> >> +     enable-uart=1<br>
>> >> >> +     kernel_address=0x200000<br>
>> >> >> +     kernel=kernel.img<br>
>> >> >> +<br>
>> >> >> +Testing using QEMU<br>
>> >> >> +------------------<br>
>> >> >> +<br>
>> >> >> +QEMU can be built using RSB. Navigate to ``<SOURCE_BUILDER_DIR>/rtems``<br>
>> >> >> +and run this command.<br>
>> >> >> +<br>
>> >> >> +.. code-block:: none<br>
>> >> >> +<br>
>> >> >> +     $ ../source-builder/sb-set-builder --prefix=<TOOLCHAIN_DIR> devel/qemu4.bset<br>
>> >> >> +<br>
>> >> >> +**Note**: Replace ``<SOURCE_BUILDER_DIR>`` and ``<TOOLCHAIN_DIR>`` with the<br>
>> >> >> +correct path of the directories. For example, if you used quick-start section<br>
>> >> >> +as your reference, these two will be ``$HOME/quick-start/src/rsb`` and<br>
>> >> >> +``$HOME/quick-start/rtems/5`` respectively,<br>
>> >> >> +<br>
>> >> >> +QEMU along with GDB can be used for debugging, but it only supports<br>
>> >> >> +Raspberry Pi 2 and the emulation is also incomplete. So some of the<br>
>> >> >> +features might not work as expected.<br>
>> >> >> +<br>
>> >> >> +Make sure your version of QEMU is newer than v2.6, because older ones don't<br>
>> >> >> +support Raspberry Pis.<br>
>> >> >> +<br>
>> >> >> +.. code-block:: none<br>
>> >> >> +<br>
>> >> >> +     $ qemu-system-arm -M raspi2 -m 1G -kernel hello.exe -serial mon:stdio -nographic -S -s<br>
>> >> >> +<br>
>> >> >> +This starts QEMU and creates a socket at port ``localhost:1234`` for GDB to<br>
>> >> >> +connect.<br>
>> >> >> +<br>
>> >> >> +The Device Tree Blob (DTB) is needed to load the device tree while starting up<br>
>> >> >> +the kernel. The BSP uses information from this file to initialize the drivers.<br>
>> >> >> +<br>
>> >> >> +Make sure you pass in the correct DTB file. There are currently two version of<br>
>> >> >> +DTB for the Raspberry Pi 2 ``bcm2709-rpi-2-b.dtb`` and ``bcm2710-rpi-2-b.dtb``.<br>
>> >> >> +The ``bcm2709-rpi-2-b.dtb`` is for Raspberry Pi 2 Model B and<br>
>> >> >> +``bcm2710-rpi-2-b.dtb`` is for Raspberry Pi 2 Model B v1.2<br>
>> >> >> +<br>
>> >> >> +We need to pass in the DTB file to GDB before running the example.<br>
>> >> >> +<br>
>> >> >> +In a new terminal, run GDB using<br>
>> >> >> +<br>
>> >> >> +.. code-block:: none<br>
>> >> >> +<br>
>> >> >> +     $ arm-rtems5-gdb hello.exe<br>
>> >> >> +<br>
>> >> >> +This will open GDB and will load the symbol table from hello.exe. Issue the<br>
>> >> >> +following commands in the GDB prompt.<br>
>> >> >> +<br>
>> >> >> +.. code-block:: none<br>
>> >> >> +<br>
>> >> >> +     (gdb) tar remote:1234<br>
>> >> >> +     (gdb) load<br>
>> >> >> +     (gdb) restore bcm2709-rpi-2-b.dtb binary 0x2ef00000<br>
>> >> >> +     (gdb) set $r2 = 0x2ef00000<br>
>> >> >> +<br>
>> >> >> +This will connect GDB to QEMU and will load the DTB file and the application.<br>
>> >> >> +<br>
>> >> >> +.. code-block:: none<br>
>> >> >> +<br>
>> >> >> +     (gdb) continue<br>
>> >> >> +<br>
>> >> >> +The ``continue`` command will run the executable.<br>
>> >> >> +<br>
>> >> >> +**Note**: Add ``set scheduler-locking on`` in GDB if you have any issues<br>
>> >> >> +running the examples.<br>
>> >> >> --<br>
>> >> >> 2.17.1<br>
>> >> >><br>
>> >> > _______________________________________________<br>
>> >> > devel mailing list<br>
>> >> > <a href="mailto:devel@rtems.org" target="_blank">devel@rtems.org</a><br>
>> >> > <a href="http://lists.rtems.org/mailman/listinfo/devel" rel="noreferrer" target="_blank">http://lists.rtems.org/mailman/listinfo/devel</a><br>
</blockquote></div></div>