[rtems-test] powerpc/psim: RTEMS_POSIX_API: Passed:615 Failed:6 Timeout:21 Test-Too-long:0 Invalid:1 Wrong:0
OAR Tester for CentOS 7
rtems-tester at oarcorp.com
Mon Sep 30 17:28:03 UTC 2024
Testing time : 0:23:44.333427
Average test time: 0:00:02.110123
Host
====
Linux-3.10.0-1160.119.1.el7.x86_64-x86_64-with-centos-7.9.2009-Core (Linux VM-CentOS7 3.10.0-1160.119.1.el7.x86_64 #1 SMP Tue Jun 4 14:43:51 UTC 2024 x86_64 x86_64)
Configuration
=============
Version: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
Build : RTEMS_POSIX_API
Tools : 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
Summary
=======
Passed: 615
Failed: 6
User Input: 6
Expected Fail: 23
Indeterminate: 0
Benchmark: 3
Timeout: 21
Test too long: 0
Invalid: 1
Wrong Version: 0
Wrong Build: 0
Wrong Tools: 0
Wrong Header: 0
------------------
Total: 675
Failures:
block05.exe
dl06.exe
fsimfsgeneric01.exe
psxkey08.exe
spfatal31.exe
ts-fatal-extension.exe
User Input:
capture.exe
dl10.exe
fileio.exe
monitor.exe
termios.exe
top.exe
Expected Fail:
imfs_fsrenameexisting.exe
imfs_fsrenamepermexisting.exe
imfs_fssymlink.exe
jffs2_fsrenameexisting.exe
jffs2_fsrenamemaxlinks.exe
jffs2_fsrenamepermexisting.exe
jffs2_fssymlink.exe
jffs2nand_fsrenameexisting.exe
jffs2nand_fsrenamemaxlinks.exe
jffs2nand_fsrenamepermexisting.exe
jffs2nand_fssymlink.exe
mdosfs_fsrenameexisting.exe
mdosfs_fsrenamemaxlinks.exe
mimfs_fsrenameexisting.exe
mimfs_fsrenamemaxlinks.exe
mimfs_fsrenamepermexisting.exe
mimfs_fssymlink.exe
mrfs_fsrenameexisting.exe
mrfs_fsrenamelongname.exe
mrfs_fsrenamemaxlinks.exe
mrfs_fsrenamepermexisting.exe
mrfs_fssymlink.exe
ts-validation-intr.exe
Benchmark:
dhrystone.exe
linpack.exe
whetstone.exe
Timeouts:
block10.exe
jffs2nand_fsrmdirparent.exe
psx11.exe
psx12.exe
psxcleanup.exe
psxcond02.exe
psxfile02.exe
psxtmsleep02.exe
sp50.exe
sp51.exe
sp63.exe
spassoc01.exe
spcache01.exe
sprmsched02.exe
stackchk04.exe
ts-fatal-idle-thread-create-failed.exe
ts-fatal-idle-thread-stack-too-small.exe
ts-userext.exe
ts-validation-1.exe
ts-validation-non-smp.exe
ts-validation-one-cpu-1.exe
Invalid:
spwkspace.exe
Log
===
RTEMS Testing - Tester, 6.0.not_released
Command Line: /home/tester/rtems-cron-6/tools/6/bin/rtems-test --rtems-tools=/home/tester/rtems-cron-6/tools/6 --rtems-bsp=psim --log=run-psim.log --use-gitconfig --mail b-psim
Host: Linux VM-CentOS7 3.10.0-1160.119.1.el7.x86_64 #1 SMP Tue Jun 4 14:43:51 UTC 2024 x86_64
Python: 2.7.5 (default, Nov 14 2023, 16:14:06) [GCC 4.8.5 20150623 (Red Hat 4.8.5-44)]
Host: Linux-3.10.0-1160.119.1.el7.x86_64-x86_64-with-centos-7.9.2009-Core (Linux VM-CentOS7 3.10.0-1160.119.1.el7.x86_64 #1 SMP Tue Jun 4 14:43:51 UTC 2024 x86_64 x86_64)
[ 1/675] p:0 f:0 u:0 e:0 I:0 B:0 t:0 L:0 i:0 W:0 | powerpc/psim: dhrystone.exe
<<skipping passes>>
[ 15/675] p:4 f:0 u:0 e:0 I:0 B:3 t:0 L:0 i:0 W:0 | powerpc/psim: fsimfsgeneric01.exe
Result: failed
Time: 0:00:05.483607 fsimfsgeneric01.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/fstests/fsimfsgeneric01.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/fstests/fsimfsgeneric01.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/fstests/fsimfsgeneric01.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/fstests/fsimfsgeneric01.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/fstests/fsimfsgeneric01.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: FSIMFSGENERIC 1
] *** BEGIN OF TEST FSIMFSGENERIC 1 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] ../../../testsuites/fstests/fsimfsgeneric01/init.c: 481 rtems_resource_snapshot_check(&before)
=> test end: FSIMFSGENERIC 1
] [ RTEMS shutdown ]
[ 16/675] p:9 f:0 u:0 e:0 I:0 B:3 t:0 L:0 i:0 W:0 | powerpc/psim: fsjffs2empty01.exe
<<skipping passes>>
[ 56/675] p:37 f:1 u:0 e:7 I:0 B:3 t:0 L:0 i:0 W:0 | powerpc/psim: jffs2nand_fsrmdirparent.exe
Result: timeout
Time: 0:03:08.023675 jffs2nand_fsrmdirparent.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/fstests/jffs2nand_fsrmdirparent.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/fstests/jffs2nand_fsrmdirparent.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/fstests/jffs2nand_fsrmdirparent.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/fstests/jffs2nand_fsrmdirparent.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/fstests/jffs2nand_fsrmdirparent.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: FSRMDIRPARENT JFFS2
] *** BEGIN OF TEST FSRMDIRPARENT JFFS2 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] Initializing filesystem JFFS2
] Testing rmdir with arguments: ".." EXPECT "-1"
] PASS
] Testing errno for ENOTEMPTY or EBUSY
] PASS
=> test end: FSRMDIRPARENT JFFS2
] *** TIMEOUT TIMEOUT
[ 57/675] p:38 f:1 u:0 e:7 I:0 B:3 t:0 L:0 i:0 W:0 | powerpc/psim: jffs2nand_fsscandir01.exe
<<skipping passes>>
[105/675] p:72 f:1 u:0 e:21 I:0 B:3 t:0 L:0 i:0 W:0 | powerpc/psim: block05.exe
Result: failed
Time: 0:00:11.915833 block05.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/libtests/block05.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/libtests/block05.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/libtests/block05.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/libtests/block05.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/libtests/block05.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: BLOCK 5
] *** BEGIN OF TEST BLOCK 5 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] T BLOCK 5 ***
=> test end: BLOCK 5
] [ RTEMS shutdown ]
[106/675] p:73 f:1 u:0 e:21 I:0 B:3 t:0 L:0 i:0 W:0 | powerpc/psim: block06.exe
<<skipping passes>>
[110/675] p:76 f:1 u:0 e:22 I:0 B:3 t:0 L:0 i:0 W:0 | powerpc/psim: block10.exe
Result: timeout
Time: 0:03:02.575010 block10.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/libtests/block10.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/libtests/block10.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/libtests/block10.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/libtests/block10.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> Quit
=> No stack.
=> You can't do that when your target is `sim'
=> test end: None
] *** TIMEOUT TIMEOUT
[111/675] p:77 f:1 u:0 e:22 I:0 B:3 t:0 L:0 i:0 W:0 | powerpc/psim: block11.exe
<<skipping passes>>
[134/675] p:99 f:2 u:0 e:22 I:0 B:3 t:0 L:0 i:0 W:0 | powerpc/psim: dl06.exe
Result: failed
Time: 0:00:07.252779 dl06.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/libtests/dl06.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/libtests/dl06.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/libtests/dl06.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/libtests/dl06.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/libtests/dl06.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: libdl (RTL) 6
] *** BEGIN OF TEST libdl (RTL) 6 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] load: /dl06.rap
] dlopen failed: global symbol not found: _tls_rand48_add
=> test end: libdl (RTL) 6
] [ RTEMS shutdown ]
[135/675] p:100 f:2 u:0 e:22 I:0 B:3 t:0 L:0 i:0 W:0 | powerpc/psim: dl07.exe
<<skipping passes>>
[183/675] p:144 f:3 u:2 e:22 I:0 B:3 t:1 L:0 i:0 W:0 | powerpc/psim: stackchk04.exe
Result: timeout
Time: 0:03:10.030844 stackchk04.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/libtests/stackchk04.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/libtests/stackchk04.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/libtests/stackchk04.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/libtests/stackchk04.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/libtests/stackchk04.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: STACKCHK04
] *** BEGIN OF TEST STACKCHK04 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] TA1 - rtems_clock_get_tod - 09:00:00 12/31/1988
] TA2 - rtems_clock_get_tod - 09:00:00 12/31/1988
] TA3 - rtems_clock_get_tod - 09:00:00 12/31/1988
] TA1 - rtems_clock_get_tod - 09:00:04 12/31/1988
] TA2 - rtems_clock_get_tod - 09:00:09 12/31/1988
] TA1 - rtems_clock_get_tod - 09:00:09 12/31/1988
] TA3 - rtems_clock_get_tod - 09:00:14 12/31/1988
] TA1 - rtems_clock_get_tod - 09:00:14 12/31/1988
] TA2 - rtems_clock_get_tod - 09:00:19 12/31/1988
] STACK USAGE BY THREAD
] ID NAME LOW HIGH CURRENT AVAIL USED
] 0x09010001 IDLE 0x00032280 0x000341ff 0x000340d8 8064 320
] 0x0a010002 TA1 0x00036428 0x0003c3af 0x0003c2d8 24456 632
] 0x0a010003 TA2 0x0003c588 0x0004250f 0x00042438 24456 408
] 0x0a010004 TA3 0x000426e8 0x0004866f 0x00048598 24456 408
] 0x00000000 Interrupt Stack 0x0002f300 0x0003127f 0x00000000 8064 528
] TA1 - rtems_clock_get_tod - 09:00:19 12/31/1988
=> test end: STACKCHK04
] *** TIMEOUT TIMEOUT
[184/675] p:145 f:3 u:2 e:22 I:0 B:3 t:1 L:0 i:0 W:0 | powerpc/psim: stringto01.exe
<<skipping passes>>
[216/675] p:174 f:3 u:4 e:22 I:0 B:3 t:2 L:0 i:0 W:0 | powerpc/psim: psx11.exe
Result: timeout
Time: 0:03:10.975835 psx11.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/psxtests/psx11.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/psxtests/psx11.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psx11.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psx11.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psx11.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: PSX 11
] *** BEGIN OF TEST PSX 11 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] Init's ID is 0x0b010001
] Init: Setting scheduling parameters to FIFO with priority 254
] Init: Setting scheduling parameters to RR with priority 252
] Init: Setting scheduling parameters to OTHER with priority 248
=> test end: PSX 11
] *** TIMEOUT TIMEOUT
[217/675] p:175 f:3 u:4 e:22 I:0 B:3 t:2 L:0 i:0 W:0 | powerpc/psim: psx12.exe
Result: timeout
Time: 0:03:10.462171 psx12.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/psxtests/psx12.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/psxtests/psx12.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psx12.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psx12.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psx12.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: PSX 12
] *** BEGIN OF TEST PSX 12 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] Init's ID is 0x0b010001
] Init: pthread_attr_init - SUCCESSFUL
] Init: pthread_create - EINVAL (invalid scheduling policy)
] Init: pthread_attr_init - SUCCESSFUL
] Init: set scheduling parameter attributes for sporadic server
=> test end: PSX 12
] *** TIMEOUT TIMEOUT
[218/675] p:176 f:3 u:4 e:22 I:0 B:3 t:2 L:0 i:0 W:0 | powerpc/psim: psx13.exe
<<skipping passes>>
[235/675] p:193 f:3 u:4 e:22 I:0 B:3 t:2 L:0 i:0 W:0 | powerpc/psim: psxcleanup.exe
Result: timeout
Time: 0:03:08.018463 psxcleanup.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/psxtests/psxcleanup.exe
=> test end: None
] *** TIMEOUT TIMEOUT
[236/675] p:194 f:3 u:4 e:22 I:0 B:3 t:2 L:0 i:0 W:0 | powerpc/psim: psxcleanup01.exe
<<skipping passes>>
[243/675] p:201 f:3 u:4 e:22 I:0 B:3 t:2 L:0 i:0 W:0 | powerpc/psim: psxcond02.exe
Result: timeout
Time: 0:03:11.234885 psxcond02.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/psxtests/psxcond02.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/psxtests/psxcond02.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psxcond02.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psxcond02.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psxcond02.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: PSXCOND 2
] *** BEGIN OF TEST PSXCOND 2 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] pthread_condattr_getclock (NULL attribute) - EINVAL
] pthread_condattr_getclock (NULL clock) - EINVAL
] pthread_condattr_setclock (NULL attribute) - EINVAL
] pthread_condattr_init - OK
] pthread_condattr_setclock (bad clock)- EINVAL
] @"&"Quit\n"
=> bt
=> test end: PSXCOND 2
] *** TIMEOUT TIMEOUT
[244/675] p:202 f:3 u:4 e:22 I:0 B:3 t:2 L:0 i:0 W:0 | powerpc/psim: psxconfig01.exe
<<skipping passes>>
[254/675] p:212 f:3 u:4 e:22 I:0 B:3 t:2 L:0 i:0 W:0 | powerpc/psim: psxfile02.exe
Result: timeout
Time: 0:03:10.253206 psxfile02.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/psxtests/psxfile02.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/psxtests/psxfile02.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psxfile02.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psxfile02.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psxfile02.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: PSXFILE 2
] *** BEGIN OF TEST PSXFILE 2 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] mkdir /tmp
] open /tmp/j
] open returned file descriptor 3
] close /tmp/j
] ftruncate an unopened file
] 9: Bad file number
] _fcntl_r an unopened file
] 9: Bad file number
] fdatasync an unopened file
] 9: Bad file number
] fstat an unopened file
] 9: Bad file number
] fsync an unopened file
] 9: Bad file number
] ioctl an unopened file
] 9: Bad file number
] _lseek_r an unopened file
] 9: Bad file number
] readv an unopened file
] 9: Bad file number
] writev an unopened file
] 9: Bad file number
] write an unopened file
] 9: Bad file number
] ftruncate a too large file descriptor
] 9: Bad file number
] _fcntl_r a too large file descriptor
] 9: Bad file number
] fdatasync a too large file descriptor
] 9: Bad file number
] fstat a too large file descriptor
] 9: Bad file number
] fsync a too large file descriptor
] 9: Bad file number
] ioctl a too large file descriptor
] 9: Bad file number
] _lseek_r a too large file descriptor
] 9: Bad file number
] readv a too large file descriptor
] 9: Bad file number
] writev a too large file descriptor
] 9: Bad file number
=> test end: PSXFILE 2
] *** TIMEOUT TIMEOUT
[255/675] p:213 f:3 u:4 e:22 I:0 B:3 t:2 L:0 i:0 W:0 | powerpc/psim: psxfilelock01.exe
<<skipping passes>>
[274/675] p:231 f:3 u:4 e:22 I:0 B:3 t:3 L:0 i:0 W:0 | powerpc/psim: psxkey08.exe
Result: failed
Time: 0:00:05.624982 psxkey08.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/psxtests/psxkey08.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/psxtests/psxkey08.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psxkey08.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psxkey08.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtests/psxkey08.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: PSXKEY 8
] *** BEGIN OF TEST PSXKEY 8 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] Init - Semaphore 1 create - OK
] Init - Semaphore 2 create - OK
] Init - pthread Key create - OK
] Init - 12 tasks have been created - OK
] Init - 12 tasks have been setted key data - OK
] Init - release semaphore 2 - OK
] Init - 12 Tasks have been got key data - OK
] Init - pthread Key delete - OK
] Init - semaphore 1 delete - OK
] Init - semaphore 2 delete - OK
] ../../../testsuites/psxtests/psxkey08/init.c: 181 rtems_resource_snapshot_check(&snapshot)
=> test end: PSXKEY 8
] [ RTEMS shutdown ]
] RTEMS version: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] RTEMS tools: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] executing thread ID: 0x0a010001
] executing thread name: UI1
=> [Inferior 1 (process 42000) exited with code 05]
[275/675] p:232 f:3 u:4 e:22 I:0 B:3 t:3 L:0 i:0 W:0 | powerpc/psim: psxkey09.exe
<<skipping passes>>
[366/675] p:318 f:4 u:4 e:22 I:0 B:3 t:7 L:0 i:0 W:0 | powerpc/psim: psxtmsleep02.exe
Result: timeout
Time: 0:03:06.905847 psxtmsleep02.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/psxtmtests/psxtmsleep02.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/psxtmtests/psxtmsleep02.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtmtests/psxtmsleep02.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtmtests/psxtmsleep02.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/psxtmtests/psxtmsleep02.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: PSXTMSLEEP 02
] *** BEGIN OF TEST PSXTMSLEEP 02 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
=> Quit
=> bt
=> No stack.
=> test end: PSXTMSLEEP 02
] *** TIMEOUT TIMEOUT
[367/675] p:320 f:4 u:4 e:22 I:0 B:3 t:7 L:0 i:0 W:0 | powerpc/psim: psxtmthread01.exe
<<skipping passes>>
[436/675] p:385 f:4 u:6 e:22 I:0 B:3 t:8 L:0 i:0 W:0 | powerpc/psim: sp50.exe
Result: timeout
Time: 0:03:08.929659 sp50.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/sptests/sp50.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/sptests/sp50.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/sp50.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/sp50.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/sp50.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: SP 50
] *** BEGIN OF TEST SP 50 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] Timer fired at 0
] Timer fired at 0
] Timer fired at 1
=> test end: SP 50
] *** TIMEOUT TIMEOUT
[437/675] p:386 f:4 u:6 e:22 I:0 B:3 t:8 L:0 i:0 W:0 | powerpc/psim: sp51.exe
Result: timeout
Time: 0:03:09.134500 sp51.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/sptests/sp51.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/sptests/sp51.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/sp51.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/sp51.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/sp51.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: SP 51
] *** BEGIN OF TEST SP 51 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] Create semaphore - priority ceiling unlocked - invalid ceiling
] Create semaphore - priority ceiling locked - violate ceiling
] Create semaphore - priority ceiling unlocked
] Obtain semaphore -- violate ceiling
] Release semaphore we did not obtain
=> test end: SP 51
] *** TIMEOUT TIMEOUT
[438/675] p:387 f:4 u:6 e:22 I:0 B:3 t:8 L:0 i:0 W:0 | powerpc/psim: sp52.exe
<<skipping passes>>
[448/675] p:397 f:4 u:6 e:22 I:0 B:3 t:8 L:0 i:0 W:0 | powerpc/psim: sp63.exe
Result: timeout
Time: 0:03:10.540899 sp63.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/sptests/sp63.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/sptests/sp63.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/sp63.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/sp63.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/sp63.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: SP 63
] *** BEGIN OF TEST SP 63 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] Init - _Heap_Initialize (for test one) - OK
] Init - Heap size=1016
] Init - _Heap_Allocate - too large size (overflow)- not OK
] Init - _Heap_Allocate_aligned - OK
] Init - _Heap_Resize_block - OK
] Init - _Heap_Initialize (for test two) - OK
] Init - Heap size=1016
=> test end: SP 63
] *** TIMEOUT TIMEOUT
[449/675] p:398 f:4 u:6 e:22 I:0 B:3 t:8 L:0 i:0 W:0 | powerpc/psim: sp64.exe
<<skipping passes>>
[463/675] p:412 f:4 u:6 e:22 I:0 B:3 t:8 L:0 i:0 W:0 | powerpc/psim: spassoc01.exe
Result: timeout
Time: 0:03:09.072901 spassoc01.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/sptests/spassoc01.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/sptests/spassoc01.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/spassoc01.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/spassoc01.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/spassoc01.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: SPASSOC 1
] *** BEGIN OF TEST SPASSOC 1 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] Init - get local by name -- OK
] Init - get local by name -- expect 0
] Init - get local by remote bitfield -- OK
] Init - get local by remote bitfield -- expect 0
] Init - get local by remote -- OK
] Init - get local by remote -- expect 0
] Init - get name by local bitfield -- OK
] Init - get name by local bitfield -- OK
] Init - get name by local bitfield -- expect""
] Init - get name by local -- OK
] Init - get name by local -- using bad value
] <assocnamebad.c: : BAD NAME>
] Init - get name by remote bitfield -- OK
] Init - get name by remote bitfield -- OK
] Init - get name by remote bitfield -- expect""
] Init - get name by remote -- OK
] Init - get name by remote -- using bad value
] <assocnamebad.c: : BAD NAME>
] Init - get ptr by local -- OK
] Init - get ptr by local -- expect NULL
] Init - get ptr by remote -- OK
] Init - get ptr by remote -- expect NULL
] Init - get ptr by name -- OK
] Init - get ptr by name -- expect NULL
] Init - get remote by local bitfield -- OK
] Init - get remote by local bitfield -- expect 0
] Init - get remote by local -- OK
=> test end: SPASSOC 1
] *** TIMEOUT TIMEOUT
[464/675] p:414 f:4 u:6 e:22 I:0 B:3 t:8 L:0 i:0 W:0 | powerpc/psim: spatomic01.exe
[465/675] p:414 f:4 u:6 e:22 I:0 B:3 t:8 L:0 i:0 W:0 | powerpc/psim: spcache01.exe
Result: timeout
Time: 0:03:09.325446 spcache01.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/sptests/spcache01.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/sptests/spcache01.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/spcache01.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/spcache01.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/spcache01.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: SPCACHE 1
] *** BEGIN OF TEST SPCACHE 1 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] data cache flush and invalidate test
] data cache operations by line passed the test (write-through cache detected)
] data cache line size 32 bytes
] data cache size 0 bytes
] load 4096 bytes with flush entire data
] duration with normal cache 1092 ns
] duration with warm cache 1092 ns
] duration with flushed cache 1092 ns
] load 4096 bytes with flush multiple data
] duration with normal cache 1092 ns
] duration with warm cache 1092 ns
] duration with flushed cache 1092 ns
] load 4096 bytes with invalidate multiple data
] duration with normal cache 1092 ns
] duration with warm cache 1092 ns
] duration with invalidated cache 1092 ns
] store 4096 bytes with flush entire data
] duration with normal cache 1093 ns
] duration with warm cache 1093 ns
] duration with flushed cache 1093 ns
] store 4096 bytes with flush multiple data
] duration with normal cache 1093 ns
] duration with warm cache 1093 ns
] duration with flushed cache 1093 ns
] store 4096 bytes with invalidate multiple data
] duration with normal cache 1093 ns
=> test end: SPCACHE 1
] *** TIMEOUT TIMEOUT
[466/675] p:415 f:4 u:6 e:22 I:0 B:3 t:8 L:0 i:0 W:0 | powerpc/psim: spcbssched01.exe
<<skipping passes>>
[566/675] p:510 f:5 u:6 e:22 I:0 B:3 t:12 L:0 i:0 W:0 | powerpc/psim: sprmsched02.exe
Result: timeout
Time: 0:03:04.123324 sprmsched02.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/sptests/sprmsched02.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/sptests/sprmsched02.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/sprmsched02.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/sprmsched02.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/sprmsched02.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: SPRMSCHED 2
] *** BEGIN OF TEST SPRMSCHED 2 ***
=> Quit
=> No stack.
=> Quit
=> You can't do that when your target is `sim'
=> quit
=> test end: SPRMSCHED 2
] *** TIMEOUT TIMEOUT
[567/675] p:511 f:5 u:6 e:22 I:0 B:3 t:12 L:0 i:0 W:0 | powerpc/psim: spscheduler01.exe
<<skipping passes>>
[610/675] p:553 f:5 u:6 e:22 I:0 B:3 t:14 L:0 i:0 W:0 | powerpc/psim: spwkspace.exe
Result: invalid
Time: 0:00:02.469981 spwkspace.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/sptests/spwkspace.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/sptests/spwkspace.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/spwkspace.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/spwkspace.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/sptests/spwkspace.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
] f"
] 0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] executing thread ID: 0x0a010001
] executing thread name: UI1
=> [Inferior 1 (process 42000) exited with code 05]
[611/675] p:553 f:5 u:6 e:22 I:0 B:3 t:14 L:0 i:0 W:0 | powerpc/psim: tm01.exe
<<skipping passes>>
[654/675] p:595 f:5 u:6 e:22 I:0 B:3 t:14 L:0 i:1 W:0 | powerpc/psim: ts-fatal-idle-thread-create-failed.exe
Result: timeout
Time: 0:03:12.422951 ts-fatal-idle-thread-create-failed.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/validation/ts-fatal-idle-thread-create-failed.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/validation/ts-fatal-idle-thread-create-failed.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-fatal-idle-thread-create-failed.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-fatal-idle-thread-create-failed.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-fatal-idle-thread-create-failed.exe
=> test start: TestsuitesFatalIdleThreadCreateFailed
] *** BEGIN OF TEST TestsuitesFatalIdleThreadCreateFailed ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] A:TestsuitesFatalIdleThreadCreateFailed
] S:Platform:RTEMS
] S:Compiler:13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] S:Version:6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] S:BSP:psim
] S:BuildLabel:DEFAULT
] S:TargetHash:SHA256:
] S:RTEMS_DEBUG:0
] S:RTEMS_MULTIPROCESSING:0
] S:RTEMS_POSIX_API:1
] S:RTEMS_PROFILING:0
] S:RTEMS_SMP:0
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
=> test end: TestsuitesFatalIdleThreadCreateFailed
] *** TIMEOUT TIMEOUT
[655/675] p:596 f:5 u:6 e:22 I:0 B:3 t:14 L:0 i:1 W:0 | powerpc/psim: ts-fatal-idle-thread-stack-too-small.exe
Result: timeout
Time: 0:03:12.520704 ts-fatal-idle-thread-stack-too-small.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/validation/ts-fatal-idle-thread-stack-too-small.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/validation/ts-fatal-idle-thread-stack-too-small.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-fatal-idle-thread-stack-too-small.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-fatal-idle-thread-stack-too-small.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-fatal-idle-thread-stack-too-small.exe
=> test start: TestsuitesFatalIdleThreadStackTooSmall
] *** BEGIN OF TEST TestsuitesFatalIdleThreadStackTooSmall ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] A:TestsuitesFatalIdleThreadStackTooSmall
] S:Platform:RTEMS
] S:Compiler:13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] S:Version:6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] S:BSP:psim
] S:BuildLabel:DEFAULT
] S:TargetHash:SHA256:
] S:RTEMS_DEBUG:0
] S:RTEMS_MULTIPROCESSING:0
] S:RTEMS_POSIX_API:1
] S:RTEMS_PROFILING:0
] S:RTEMS_SMP:0
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
=> test end: TestsuitesFatalIdleThreadStackTooSmall
] *** TIMEOUT TIMEOUT
[656/675] p:597 f:5 u:6 e:22 I:0 B:3 t:14 L:0 i:1 W:0 | powerpc/psim: ts-fatal-init-task-construct-failed.exe
<<skipping passes>>
[660/675] p:601 f:6 u:6 e:22 I:0 B:3 t:14 L:0 i:1 W:0 | powerpc/psim: ts-userext.exe
Result: timeout
Time: 0:03:13.544093 ts-userext.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/validation/ts-userext.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/validation/ts-userext.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-userext.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-userext.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-userext.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: TestsuitesUserext
] *** BEGIN OF TEST TestsuitesUserext ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] A:TestsuitesUserext
] S:Platform:RTEMS
] S:Compiler:13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] S:Version:6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] S:BSP:psim
] S:BuildLabel:DEFAULT
] S:TargetHash:SHA256:FxbUPMFAfdnPCU2b0Y4l-hl4WMdj1U-2DWddZSVVsUA=
] S:RTEMS_DEBUG:0
] S:RTEMS_MULTIPROCESSING:0
] S:RTEMS_POSIX_API:1
] S:RTEMS_PROFILING:0
] S:RTEMS_SMP:0
] B:RtemsUserextValUserext
=> 90 _bt->sec += _bt2->sec;
=> #6 0x00007c58 in clockIsr (unused=<optimized out>) at ../../../bsps/powerpc/shared/clock/clock-ppc-dec.c:164
=> test end: TestsuitesUserext
] *** TIMEOUT TIMEOUT
[661/675] p:601 f:6 u:6 e:22 I:0 B:3 t:14 L:0 i:1 W:0 | powerpc/psim: ts-validation-0.exe
[662/675] p:602 f:6 u:6 e:22 I:0 B:3 t:14 L:0 i:1 W:0 | powerpc/psim: ts-validation-1.exe
Result: timeout
Time: 0:03:41.805005 ts-validation-1.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/validation/ts-validation-1.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/validation/ts-validation-1.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-validation-1.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-validation-1.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-validation-1.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: TestsuitesValidation1
] *** BEGIN OF TEST TestsuitesValidation1 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] A:TestsuitesValidation1
] S:Platform:RTEMS
] S:Compiler:13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] S:Version:6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] S:BSP:psim
] S:BuildLabel:DEFAULT
] S:TargetHash:SHA256:FxbUPMFAfdnPCU2b0Y4l-hl4WMdj1U-2DWddZSVVsUA=
] S:RTEMS_DEBUG:0
] S:RTEMS_MULTIPROCESSING:0
] S:RTEMS_POSIX_API:1
] S:RTEMS_PROFILING:0
] S:RTEMS_SMP:0
] B:RtemsTaskReqConstruct
] E:RtemsTaskReqConstruct:N:196804:F:0:D:0.755093
=> test end: TestsuitesValidation1
] *** TIMEOUT TIMEOUT
[663/675] p:603 f:6 u:6 e:22 I:0 B:3 t:14 L:0 i:1 W:0 | powerpc/psim: ts-validation-acfg-0.exe
<<skipping passes>>
[669/675] p:608 f:6 u:6 e:22 I:0 B:3 t:15 L:0 i:1 W:0 | powerpc/psim: ts-validation-non-smp.exe
Result: timeout
Time: 0:03:09.514394 ts-validation-non-smp.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/validation/ts-validation-non-smp.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/validation/ts-validation-non-smp.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-validation-non-smp.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-validation-non-smp.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-validation-non-smp.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: TestsuitesValidationNonSmp
] *** BEGIN OF TEST TestsuitesValidationNonSmp ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] A:TestsuitesValidationNonSmp
] S:Platform:RTEMS
] S:Compiler:13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] S:Version:6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] S:BSP:psim
=> test end: TestsuitesValidationNonSmp
] *** TIMEOUT TIMEOUT
[670/675] p:609 f:6 u:6 e:22 I:0 B:3 t:15 L:0 i:1 W:0 | powerpc/psim: ts-validation-one-cpu-0.exe
[671/675] p:610 f:6 u:6 e:22 I:0 B:3 t:15 L:0 i:1 W:0 | powerpc/psim: ts-validation-one-cpu-1.exe
Result: timeout
Time: 0:03:40.452360 ts-validation-one-cpu-1.exe
=> gdb: /home/tester/rtems-cron-6/tools/6/bin/powerpc-rtems6-gdb -i=mi --nx --quiet b-psim/powerpc/psim/testsuites/validation/ts-validation-one-cpu-1.exe
=> Reading symbols from b-psim/powerpc/psim/testsuites/validation/ts-validation-one-cpu-1.exe...
=> warning: File "/home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-validation-one-cpu-1.exe" auto-loading has been declined by your `auto-load safe-path' set to "$debugdir:$datadir/auto-load".
=> To enable execution of this file add
=> add-auto-load-safe-path
=> /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-validation-one-cpu-1.exe
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> To completely disable this security protection add
=> set auto-load safe-path /
=> line to your configuration file "
=> /home/tester/.config/gdb/gdbinit".
=> For more information about this security protection see the
=> "Auto-loading safe path" section in the GDB manual. E.g., run from the shell:
=> info "(gdb)Auto-loading safe path"
=> target sim -f /home/tester/rtems-cron-6/tools/6/share/rtems/tester/rtems/testing/bsps/psim-device-tree
=> Connected to the simulator.
=> load
=> run
=> Starting program: /home/tester/rtems-cron-6/rtems/b-psim/powerpc/psim/testsuites/validation/ts-validation-one-cpu-1.exe
] OpenPIC Version 1.2 (2 CPUs and 17 IRQ sources) at 0x4229103616
] OpenPIC Vendor 0 (Unknown), Device 0 (Unknown), Stepping 0
] Overriding NumSources (17) from configuration with 16
] OpenPIC timer frequency is 1 Hz
] BATs must not overlap; area 0x08000000..0x09000000 hits DBAT 0
=> test start: TestsuitesValidationOneCpu1
] *** BEGIN OF TEST TestsuitesValidationOneCpu1 ***
] *** TEST VERSION: 6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] *** TEST STATE: EXPECTED_PASS
] *** TEST BUILD: RTEMS_POSIX_API
] *** TEST TOOLS: 13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] A:TestsuitesValidationOneCpu1
] S:Platform:RTEMS
] S:Compiler:13.3.0 20240521 (RTEMS 6, RSB d2f00ca6c06f0f5c78eab1128121e9c58fba0443, Newlib 1b3dcfd)
] S:Version:6.0.0.38bafce42de94a7408760ccfca059b0681d77d51
] S:BSP:psim
] S:BuildLabel:DEFAULT
] S:TargetHash:SHA256:FxbUPMFAfdnPCU2b0Y4l-hl4WMdj1U-2DWddZSVVsUA=
] S:RTEMS_DEBUG:0
] S:RTEMS_MULTIPROCESSING:0
] S:RTEMS_POSIX_API:1
] S:RTEMS_PROFILING:0
] S:RTEMS_SMP:0
] B:RtemsTaskReqConstruct
] E:temsTaskReqConstruct:N:196804:F:0:D:0.721770
] B:AcfgValSchedulerTableEntriesOneCpu
=> test end: TestsuitesValidationOneCpu1
] *** TIMEOUT TIMEOUT
[672/675] p:611 f:6 u:6 e:22 I:0 B:3 t:15 L:0 i:1 W:0 | powerpc/psim: ts-validation-timecounter-0.exe
<<skipping passes>>
[675/675] p:613 f:6 u:6 e:23 I:0 B:3 t:15 L:0 i:1 W:0 | powerpc/psim: ts-validation-tls-1.exe
Passed: 615
Failed: 6
User Input: 6
Expected Fail: 23
Indeterminate: 0
Benchmark: 3
Timeout: 21
Test too long: 0
Invalid: 1
Wrong Version: 0
Wrong Build: 0
Wrong Tools: 0
Wrong Header: 0
------------------
Total: 675
Failures:
block05.exe
dl06.exe
fsimfsgeneric01.exe
psxkey08.exe
spfatal31.exe
ts-fatal-extension.exe
User Input:
capture.exe
dl10.exe
fileio.exe
monitor.exe
termios.exe
top.exe
Expected Fail:
imfs_fsrenameexisting.exe
imfs_fsrenamepermexisting.exe
imfs_fssymlink.exe
jffs2_fsrenameexisting.exe
jffs2_fsrenamemaxlinks.exe
jffs2_fsrenamepermexisting.exe
jffs2_fssymlink.exe
jffs2nand_fsrenameexisting.exe
jffs2nand_fsrenamemaxlinks.exe
jffs2nand_fsrenamepermexisting.exe
jffs2nand_fssymlink.exe
mdosfs_fsrenameexisting.exe
mdosfs_fsrenamemaxlinks.exe
mimfs_fsrenameexisting.exe
mimfs_fsrenamemaxlinks.exe
mimfs_fsrenamepermexisting.exe
mimfs_fssymlink.exe
mrfs_fsrenameexisting.exe
mrfs_fsrenamelongname.exe
mrfs_fsrenamemaxlinks.exe
mrfs_fsrenamepermexisting.exe
mrfs_fssymlink.exe
ts-validation-intr.exe
Benchmark:
dhrystone.exe
linpack.exe
whetstone.exe
Timeouts:
block10.exe
jffs2nand_fsrmdirparent.exe
psx11.exe
psx12.exe
psxcleanup.exe
psxcond02.exe
psxfile02.exe
psxtmsleep02.exe
sp50.exe
sp51.exe
sp63.exe
spassoc01.exe
spcache01.exe
sprmsched02.exe
stackchk04.exe
ts-fatal-idle-thread-create-failed.exe
ts-fatal-idle-thread-stack-too-small.exe
ts-userext.exe
ts-validation-1.exe
ts-validation-non-smp.exe
ts-validation-one-cpu-1.exe
Invalid:
spwkspace.exe
Average test time: 0:00:02.110123
Testing time : 0:23:44.333427
More information about the build
mailing list